Recycling plastics from end-of-life vehicles (ELVs) is central to improving resource recovery and moving plastics toward more circular use. Among the available routes, pyrolysis has drawn attention as a way to recover fuels and chemicals from waste polymers.
The process breaks down plastics thermally at elevated temperatures in the absence of oxygen, splitting polymer chains into liquid, gaseous and solid products. Earlier work has shown that common automotive plastics — low-density polyethylene (LDPE), high-density polyethylene (HDPE) and polypropylene (PP) — can be converted into valuable hydrocarbons at relatively high yields.
A gap around real component plastics
Much of that research, however, has focused on automotive shredder residue, a heterogeneous mixture of plastics, metals, textiles and other materials. Less is known about how plastics recovered directly from components such as dashboards, bumpers and headlamps behave during pyrolysis. Automotive plastic waste (APW) can also carry mineral fillers, flame retardants, fiberglass and other additives that influence degradation behaviour and product composition.
Catalysts offer one way to improve pyrolysis efficiency, accelerating reactions, shifting product distributions and potentially lowering the temperature or residence time required. Commercial zeolites have been widely studied, but lower-cost clay-based alternatives are attracting growing interest. Pillared clays modified with metals such as iron, titanium or zirconium have shown potential to raise liquid yields and influence the formation of fuel-range hydrocarbons; iron-modified clays are considered particularly attractive because they may improve oil production without relying on more expensive commercial catalysts.
How the study was set up
The researchers characterised plastics recovered directly from ELVs rather than relying on mixed shredder residue. The feedstock contained acrylonitrile butadiene styrene (ABS), HDPE and LDPE, PP, polystyrene (PS) and fiberglass, and it also held substantial volatile and ash fractions. Front and rear bumpers accounted for 86.6% of the sample by weight, while fiberglass, used to reinforce automotive components, contributed to the relatively high ash content.
Instead of using bentonite clay as received, the team modified it through iron pillaring — a process that introduces iron species into the clay structure and changes characteristics such as surface acidity and pore structure that can influence pyrolysis reactions. The study compared thermal and catalytic pyrolysis across temperatures from roughly 350°C to 521°C and catalyst loadings of about 6% to 34% by weight, using a statistical experimental design to evaluate how temperature and catalyst concentration interacted.
Higher yield, mostly unchanged composition
The catalyst had a strong effect on liquid yield. Catalytic pyrolysis produced an average oil yield of approximately 68%, compared with 41% for thermal pyrolysis alone. The highest oil yield, 78.6%, was reached at about 416°C with a catalyst loading of roughly 24%.
Its influence on oil composition was far weaker. Thermal and catalytic runs produced similar proportions of hydrocarbons in the C8–C24 range associated with gasoline- and diesel-range compounds. In other words, the catalyst helped convert more of the feedstock into liquid product, but did not substantially shift that liquid toward a higher share of diesel-range molecules.
Temperature mattered more for composition. Lower pyrolysis temperatures favoured diesel-range organics, while temperatures above 450°C produced a heavier, waxier oil.
The results draw a fairly clear line between two things a catalyst can do: raise how much of the feedstock becomes liquid, and change what that liquid is made of. The iron-pillared clay clearly did the first; within the C8–C24 window the researchers examined, it did little of the second. For a process aimed at diesel-range fuel, that distinction matters, because a higher oil yield only helps if the extra liquid can be brought to meet fuel specifications.
Fuel properties and their limits
The resulting pyrolysis oil showed several properties comparable to commercial diesel. The researchers reported a calorific value of 49.85 MJ/kg, a flash point of 113°C and total aromatics of 3.55% by area — values within or comparable to ranges specified for conventional fuels. Branched heptenes and heptanes dominated the oil, compounds also identified in earlier studies of polypropylene and automotive-plastic pyrolysis.
Not every property met diesel specifications. Both density and viscosity exceeded the limits typically specified for diesel fuel, which the researchers attributed partly to heavier, long-chain hydrocarbon fractions remaining in the oil.
Additional processing could therefore be needed before the oil can be used as a diesel-range fuel. The researchers pointed to approaches such as distillation and centrifugation, as well as optimising reaction conditions through lower temperatures and longer residence times, to reduce heavier fractions and improve fuel properties.
What comes next
The study positions pyrolysis as a technically promising route for recovering value from automotive plastics, while also underscoring the development still required before the process can move toward broader commercial application. Future work could investigate different iron concentrations in the catalyst, improve reactor designs and heat transfer, and combine pyrolysis with downstream distillation to separate gasoline- and diesel-range fractions.
Temperature, meanwhile, emerged as the stronger lever over composition, giving operators a way to steer the process toward lighter, diesel-range molecules by running at the lower end of the tested window. The study reports the conditions that maximised oil yield, but matching those conditions to the best achievable fuel properties — and reliably minimising the heavier fractions that push density and viscosity above diesel limits — would require further work.
Improved collection and sorting of automotive plastics will also matter. Without systematic removal and classification of plastic components from end-of-life vehicles, reliable data on the volume and composition of available automotive plastic waste remain limited. Better information on these waste streams would help researchers and recyclers assess feedstock availability and plan potential industrial-scale pyrolysis operations.
